Differences between revisions 17 and 18

NE2000 ISA clone FAQ

How to deal with ISA Plug n Play cards and still have a shread of sanity left at the end of the day.

In the beginning ....

Plug and Play (PNP)

After the jumper, but before PCI there was PNP. When it was new it was a disaster. It hasn't gotten much better. It was just another weak attempt to emulate the simplicity of MAC hardware. ISA cards have two modes; jumpered and jumperless.

Jumpered

YOU must physically move a jumper on the card to change configuration

Jumperless'

A Dos program is used to write the config to a flash memory on the board itself. This emulates a jumpered device. In this mode a device is usually NOT in PNP mode.

'EISA' Don't ask.

The ISA Board config problem.

There are two kinds of basic ISA boards. The ISA boards with jumpers and those without. A board with jumpers is pretty straightforward. Read the ISA board (If you can), and place the jumpers. If the board is especially cheap, the jumpers will not have any marks or writing near them. Your next step would be to Google the ISA board by the chipset number.

Ethernet chips come from a small number of manufacturers. Those FABS sell or license the chips to other companies. The NE2000 was originally made for Novell Ethernet, (NE). The 2000 was used most likely because it was so "futuristic". The NE2000 spec became one of the most used network specs.

The ISA Ethernet board comes in a number of manufacturers chips. Most smaller manufacturers buy chips from a large chip house and rebrand them as their own. If you look at the small number of ethernet drivers that Linux distributions come with, you will notice there are not many drivers as there are ethernet cards. These many drivers cover many different network chips. Here is a list of the most commonly found NE200 chips.

Realtek 8019
Realtek 8029
Anthem/Novell NE2000
SMC EZ
DAVICOM DM9008F
WINBOND W89C904AXF
WINBOND W89C904F
WINBOND W89C905F
WINBOND W89C906F
WINBOND W89C906F
UMC UM9003AF
UMC UM9007
UMC UM9008
AT/LANTIC (Allied Tellisys)

Tips

"Don't use addresses 0x300 or 0x320 for NE2000 type cards." [Ethernet Howto] Most ISA modules accept parameters like io=0x340 and irq=12 on the insmod command line. It is REQUIRED or at least STRONGLY ADVISED that you supply these parameters to avoid probing for the card. Unlike PCI and EISA devices, there is no real safe way to do auto-probing for most ISA devices, and so it should be avoided when using drivers as modules. [Ethernet Howto]

There are two major pieces of information needed for configuring the ISA PnP card.

1. IRQ. The Interrupt Request. A number between 2 and fifteen.

Interrupts 3 and 4 are for serial ports. Five is for a second printer port or a sound card. IRQ 6 is used for the Floppy drive controller. IRQ 7 is sometimes used for sound cards but most often used for the first parallel, (printer) port. IRQ 8 is for the Real Time Clock, Don't mess with this one.

IRQ 9 is a mutant interrupt, unlike any other. IRQ 9 IS IRQ 2 in disguise. I don't think there is a network card alive today that will allow you to use IRQ2, but 9 is OK almost always. Now we come to my favorite of all interrupts. Number TEN. More to come...

2. The ADDRESS. The I/O address is the place where your ISA board has been told to live either by a jumper or by a configuration program. The address is a memory address where the driver will be loaded
3. FIRST Turn OFF Plug and Play in BIOS. Did you turn off PNP in BIOS? Are you sure?

---

Things you should have learned in school, (had you been paying attention).

1. PORT SENSING Newer Ethernet cards will sense the active port Twisted Pair, Co-AX. Older cards must be jumpered or tweaked with the setup software.
2. Connectors.

Your ISA eternet card may have up to THREE different connectors.

a 10base5 Distance 500 meters Connector DB15 Male.
b 10 base 5. not used for much anymore. But the 5 stands for 500 meters, which is how long the wire can be to the next ethernet port. It looks like a "GAME" connector.
c 10baseT Distance 100 meters. Connector: RJ45 (Oversized phone plug)
c 10base2 distance 200 meters. Connector: BNC Barrel tubular shaft protruding from your ethernet card

Credits and links:

http://www.plasma-online.de/index.html?content=http%3A//www.plasma-online.de/english/identify/serial/pnp_id_pnp.html

The ISA PNP FAQ http://www.roestock.demon.co.uk/isapnptools/

NE2000 Clone Configuration programs http://www.corbina.ru/~gasya/homelan/drivers/ne2000.htm

Linux Ethercard Status, Diagnostic and Setup Utilities http://www.scyld.com/diag/index.html

-  ← Revision 17 as of 2002-04-11 16:24:05 →
  Size: 4626
  Editor: 205
  Comment:
+  ← Revision 18 as of 2002-04-11 16:39:21 →
  Size: 4801
  Editor: 205
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 10:
  * '''Jumpered'''
 Line 19:
-Ethernet chips come from a small number of manufacturers. Those FABS sell or license the chips to other companies.
+Ethernet chips come from a small number of manufacturers. Those FABS sell or license the chips to other companies. The NE2000 was originally made for Novell Ethernet, (NE). The 2000 was used most likely because it was so "futuristic". The NE2000 spec became one of the most used network specs.
 Line 21:
 The ISA Ethernet board comes in a number of manufacturers chips. Most smaller manufacturers buy chips from a large chip house and rebrand them as their own. If you look at the small number of ethernet drivers that Linux distributions come with, you will notice there are not many drivers as there are ethernet cards. These many drivers cover many different network chips. Here is a list of the most commonly found NE200 chips.
-Line 40:
+Line 41:
 "Don't use addresses 0x300 or 0x320 for NE2000 type cards."
-Line 53:
+Line 54:
 IRQ 9 is a mutant interrupt, unlike any other. IRQ 9 IS IRQ 2 in disguise. I don't think there is a network card alive today that will allow you to use IRQ2, but 9 is OK almost always. Now we come to my 	favorite of all interrupts.
-Line 65:
+Line 66:
  * 2. Connectors.