Size: 3644
Comment:
|
Size: 3703
Comment: Changed formatting so it doesn't look like an error, linked to more wiki content
|
Deletions are marked like this. | Additions are marked like this. |
Line 2: | Line 2: |
An accessible and concise guide to basic troubleshooting when a node goes awry. | |
Line 3: | Line 4: |
This document is a new attempt to make accessible and concise documentation for the type of basic troubleshooting that must be done when a node is acting awry. [[TableOfContents]] |
<<TableOfContents>> |
Line 13: | Line 10: |
This version is current as of: [[Date]] | This version is current as of: <<Date>> |
Line 16: | Line 13: |
This section assumes you have a wireless-enabled device, and that you're unable to connect to a [[PotentialNodeOwnerFaq|Personal Telco node]]. This document is a flowchart: start at the first step and work your way through until you solve the problem. | |
Line 17: | Line 15: |
This section assumes that you have a laptop that has a wireless client device which will allow you (when functioning) to use the node. This document works like a flowchart: you start at the first step and work your way through successive steps until you reach a goal. |
=== Step 1: Can you see the ESSID? === Each access point your computer can see is identified by its ESSID (or Network Name). A Personal Telco node, by definition, uses "www.personaltelco.net" as its ESSID. Your computer will have some software that lets you pick the access point you connect to by the ESSID. If you can see "www.personaltelco.net" in this list, goto 4, otherwise, goto 3. |
Line 22: | Line 18: |
=== 1. Can you see the ESSID? === |
=== Step 2: Contact the PTP === At this point, this document can't save you. Please contact us at info@personaltelco.net, describing the problem you have and what you tried using this document as guidance (and possibly things you tried without guidance). |
Line 24: | Line 21: |
Each access point your computer can see, is identified by it's ESSID (or Network Name). A Personal Telco node, by definition uses "www.personaltelco.net" as its ESSID. Your computer will have some software that lets you pick the access point you connect to by the ESSID, if you can see "www.personaltelco.net" in this list, goto 4, otherwise, goto 3. |
Please let us know if this document was (or wasn't) helpful. |
Line 29: | Line 23: |
=== 2. Contact the PTP === |
=== Step 3: Make sure the Access Point has Power === Your [[AccessPoint|access point]] is most likely a small device with an antenna connected to it. Find it, and make sure it is powered on. If it is, goto 2, otherwise, plug it in and goto 1. |
Line 31: | Line 26: |
At this point, this document can't save you. Please contact us at info@personaltelco.net, describing the problem you have and what you tried using this document as guidance (and possibly things you tried without guidance). Please let us know if this document was helpful. === 3. Make sure the Access Point has Power === Your access point is (most likely) a small device with an antenna connected to it. Find it, and make sure it is getting power. If it is, goto 2, otherwise, plug it in and goto 1. === 4. Get an IP Address === Your laptop should get an IP address from the Node. If you have windows, try this: |
=== Step 4: Get an IP Address === Your device should get an IP address from the Node. If you have Windows, try this: |
Line 50: | Line 33: |
Do you see an ip address? Most likely it looks something like: (TODO: add screen shot) |
Do you see an IP address? Most likely it looks something like: "192.168.0.101" (TODO: [[NeedsUpdate|add screen shot]]) |
Line 62: | Line 45: |
=== 5. Open a Webpage === | === Step 5: Open a Webpage === |
Line 64: | Line 47: |
Open your web-browser. Cool people use "Firefox", less cool people use "Internet Explorer". Goto a webpage, like this one: http://www.google.com. Can you see it? If you have a captive portal, you should see the splash page (with the Personal Telco logo), if so, try clicking "Accept" and then going to http://www.google.com. At this point, You should see the Google logo... If so, goto 6, otherwise goto one of these: |
Open your web-browser. Cool people use "Firefox", less cool people use "Internet Explorer". Open any webpage, e.g. http://www.google.com. Can you see it? If you have a [[CaptivePortal|captive portal]], you should see the [[SplashPage|splash page]] (with the Personal Telco logo) - if so, click "Accept", and then visit http://www.google.com. At this point, you should see the Google logo... If so, goto 6, otherwise goto one of these: |
Line 73: | Line 55: |
=== 6. Everything is Okay? === | === Step 6: Everything is Okay? === |
Line 75: | Line 57: |
If you reached here, it seems like all is well. Is it not? Perhaps you have a problem this document cannot prepare you for. Goto 2. |
If you reached here, it seems like all is well. Is it not? Perhaps you have a problem this document cannot prepare you for. Goto 2. |
Line 78: | Line 59: |
=== 7. Investigate Wiring Problems === | === Step 7: Investigate Wiring Problems === |
Line 80: | Line 61: |
[http://www.personaltelco.net/~caleb/diagrams/PotentialNodeOwner2.png] | [[http://www.personaltelco.net/~caleb/diagrams/PotentialNodeOwner2.png]] |
Line 82: | Line 63: |
Your setup, might look something like the above diagram. You will have a DSL modem, a Access Point, and often, a Captive Portal. Make sure these are connected to each other as shown. Also, at each connection check for a little green light - this is the "Link Light", if it isn't lit, then either the other end is disconnected or the wire is damaged. If you think everything is connected properly, goto 2. If not, do your best to connect the devices as shown in the diagram, if it still doesn't work - go to 2. |
Your setup might look something like the above diagram. You will have a DSL modem, a Access Point, and often, a [[CaptivePortal|Captive Portal]]. Make sure these are connected to each other as shown. Also, at each connection check for a little green light - this is the "Link Light." If it isn't lit, then either the other end is disconnected or the wire is damaged. If you think everything is connected properly, goto 2. If not, do your best to connect the devices as shown in the diagram, if it still doesn't work - go to 2. |
Line 92: | Line 67: |
Created by DonPark and CalebPhillips over beers at NodeLuckyLab. | Created by DonPark and CalebPhillips over beers at NodeLuckyLab. Updated -- DanRasmussen <<DateTime(2012-04-02T12:56:33-0800)>> |
Node Owner Help
An accessible and concise guide to basic troubleshooting when a node goes awry.
Contents
The most recent version of this document will always live here:
http://wiki.personaltelco.net/index.cgi/NodeOwnerHelp
This version is current as of: 2025-07-23
Troubleshooting
This section assumes you have a wireless-enabled device, and that you're unable to connect to a Personal Telco node. This document is a flowchart: start at the first step and work your way through until you solve the problem.
Step 1: Can you see the ESSID?
Each access point your computer can see is identified by its ESSID (or Network Name). A Personal Telco node, by definition, uses "www.personaltelco.net" as its ESSID. Your computer will have some software that lets you pick the access point you connect to by the ESSID. If you can see "www.personaltelco.net" in this list, goto 4, otherwise, goto 3.
Step 2: Contact the PTP
At this point, this document can't save you. Please contact us at info@personaltelco.net, describing the problem you have and what you tried using this document as guidance (and possibly things you tried without guidance).
Please let us know if this document was (or wasn't) helpful.
Step 3: Make sure the Access Point has Power
Your access point is most likely a small device with an antenna connected to it. Find it, and make sure it is powered on. If it is, goto 2, otherwise, plug it in and goto 1.
Step 4: Get an IP Address
Your device should get an IP address from the Node. If you have Windows, try this:
goto Start -> Run
- type "cmd", Enter
- in the black box, type "ipconfig", Enter
Do you see an IP address? Most likely it looks something like: "192.168.0.101" (TODO: add screen shot)
If not, try
- in the black box, type "ipconfig /release", Enter
- then type, "ipconfig /renew", Enter
- finally type, "ipconfig", Enter
Do you see an IP address now? If not, goto 7, otherwise goto 5.
Step 5: Open a Webpage
Open your web-browser. Cool people use "Firefox", less cool people use "Internet Explorer". Open any webpage, e.g. http://www.google.com. Can you see it? If you have a captive portal, you should see the [[SplashPage|splash page]] (with the Personal Telco logo) - if so, click "Accept", and then visit http://www.google.com. At this point, you should see the Google logo... If so, goto 6, otherwise goto one of these:
- Goto 7 if it says something like "www.google.com cannot be found"
- Goto 7 if it says something like "... is not responding" or "... cannot be contacted
Step 6: Everything is Okay?
If you reached here, it seems like all is well. Is it not? Perhaps you have a problem this document cannot prepare you for. Goto 2.
Step 7: Investigate Wiring Problems
http://www.personaltelco.net/~caleb/diagrams/PotentialNodeOwner2.png
Your setup might look something like the above diagram. You will have a DSL modem, a Access Point, and often, a Captive Portal. Make sure these are connected to each other as shown. Also, at each connection check for a little green light - this is the "Link Light." If it isn't lit, then either the other end is disconnected or the wire is damaged. If you think everything is connected properly, goto 2. If not, do your best to connect the devices as shown in the diagram, if it still doesn't work - go to 2.
Credits
Created by DonPark and CalebPhillips over beers at NodeLuckyLab. Updated -- DanRasmussen 2012-04-02 12:56:33