|
Size: 3646
Comment: converted to 1.6 markup
|
← Revision 14 as of 2012-04-06 13:53:43
Size: 3765
Comment: Wording, modernized and made friendlier to the non-tech
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| An accessible and concise guide to basic troubleshooting internet connection problems with a Personal Telco node. | |
| Line 3: | Line 4: |
|
This document is a new attempt to make accessible and concise documentation for the type of basic troubleshooting that must be done when a node is acting awry. |
The most recent version of this document will always live here: [[https://personaltelco.net/wiki/NodeOwnerHelp]]. The version you are viewing is current as of <<Date>>. |
| Line 9: | Line 8: |
| The most recent version of this document will always live here: |
== Troubleshooting == This section assumes you have a wireless-enabled device, and that you're unable to connect to a [[PotentialNodeOwnerFaq|Personal Telco node]]. This is a flowchart: start at the first step and work your way through until you solve the problem. |
| Line 11: | Line 11: |
| http://wiki.personaltelco.net/index.cgi/NodeOwnerHelp |
=== Step 1. Can you see the ESSID? === Each wireless network your computer can see is identified by its ESSID (or Network Name). A Personal Telco node, by definition, has an ESSID of "www.personaltelco.net". If you can see "www.personaltelco.net" in your computer's list of available wireless networks, go to Step 4, otherwise, go to Step 3. |
| Line 13: | Line 14: |
| This version is current as of: <<Date>> |
=== Step 2. Contact the PTP === If you've arrived at Step 2, the solution to your technical issues isn't covered in this troubleshooting guide. Please contact us at info@personaltelco.net, describing the problem and the steps you've taken to solve it. |
| Line 15: | Line 17: |
| == Troubleshooting == | Please let us know if this document was (or wasn't) helpful. |
| Line 17: | Line 19: |
|
This section assumes that you have a laptop that has a wireless client device which will allow you (when functioning) to use the node. This document works like a flowchart: you start at the first step and work your way through successive steps until you reach a goal. |
=== Step 3. Make sure the Access Point has Power === Your [[AccessPoint|access point]] is most likely a small device with an antenna connected to it. Find it, and make sure it is powered on. If it is, go to Step 2, otherwise, plug it in and go to Step 1. |
| Line 22: | Line 22: |
| === 1. Can you see the ESSID? === |
=== Step 4. Get an IP Address === Your device should get an IP address from the Node. If you use Windows, try this: |
| Line 24: | Line 25: |
|
Each access point your computer can see, is identified by it's ESSID (or Network Name). A Personal Telco node, by definition uses "www.personaltelco.net" as its ESSID. Your computer will have some software that lets you pick the access point you connect to by the ESSID, if you can see "www.personaltelco.net" in this list, goto 4, otherwise, goto 3. === 2. Contact the PTP === At this point, this document can't save you. Please contact us at info@personaltelco.net, describing the problem you have and what you tried using this document as guidance (and possibly things you tried without guidance). Please let us know if this document was helpful. === 3. Make sure the Access Point has Power === Your access point is (most likely) a small device with an antenna connected to it. Find it, and make sure it is getting power. If it is, goto 2, otherwise, plug it in and goto 1. === 4. Get an IP Address === Your laptop should get an IP address from the Node. If you have windows, try this: * goto Start -> Run |
* go to Start -> Run |
| Line 50: | Line 29: |
| Do you see an ip address? Most likely it looks something like: |
Do you see an IP address? Most likely it looks something like: "192.168.0.101" (TODO: [[NeedsUpdate|add screen shot]]) |
| Line 52: | Line 33: |
|
(TODO: add screen shot) If not, try |
If not, try this: |
| Line 60: | Line 39: |
| Do you see an IP address now? If not, goto 7, otherwise goto 5. | Do you see an IP address now? If not, go to Step 7, otherwise go to Step 5. |
| Line 62: | Line 41: |
| === 5. Open a Webpage === | === Step 5. Open a Webpage === |
| Line 64: | Line 43: |
|
Open your web-browser. Cool people use "Firefox", less cool people use "Internet Explorer". Goto a webpage, like this one: http://www.google.com. Can you see it? If you have a captive portal, you should see the splash page (with the Personal Telco logo), if so, try clicking "Accept" and then going to http://www.google.com. At this point, You should see the Google logo... If so, goto 6, otherwise goto one of these: |
Open your web browser -- we recommend [[RealBrowser|Mozilla Firefox]], if available for your device, and recommend not using [[RealBrowser|Internet Explorer]]. |
| Line 70: | Line 45: |
|
* Goto 7 if it says something like "www.google.com cannot be found" * Goto 7 if it says something like "... is not responding" or "... cannot be contacted |
Open any webpage, e.g. ''http://google.com''. Can you see it? If you have a [[CaptivePortal|captive portal]], you should see the [[SplashPage|splash page]] (with the Personal Telco logo) - if so, click "Accept", then visit ''http://google.com''. |
| Line 73: | Line 47: |
| === 6. Everything is Okay? === | At this point, you should see the website you wanted (e.g. Google) If so, go to Step 6. Otherwise: |
| Line 75: | Line 49: |
|
If you reached here, it seems like all is well. Is it not? Perhaps you have a problem this document cannot prepare you for. Goto 2. |
* Go to Step 7 if it says something like "''google.com'' cannot be found" * Go to Step 7 if it says something like "... is not responding" or "... cannot be contacted |
| Line 78: | Line 52: |
| === 7. Investigate Wiring Problems === |
=== Step 6. Everything is Okay? === If you reached here, it seems like all is well. If not, perhaps you have a problem not covered in this document: go to Step 2. === Step 7. Investigate Wiring Problems === |
| Line 82: | Line 60: |
|
Your setup, might look something like the above diagram. You will have a DSL modem, a Access Point, and often, a Captive Portal. Make sure these are connected to each other as shown. Also, at each connection check for a little green light - this is the "Link Light", if it isn't lit, then either the other end is disconnected or the wire is damaged. If you think everything is connected properly, goto 2. If not, do your best to connect the devices as shown in the diagram, if it still doesn't work - go to 2. |
Your setup might look something like the above diagram. You will have a DSL modem, a Access Point, and often, a [[CaptivePortal|Captive Portal]]. Make sure these are connected to each other as shown. Also, at each connection check for a little green light - this is the "Link Light." If it isn't lit, then either the other end is disconnected or the wire is damaged. If you think everything is connected properly, go to Step 2. If not, do your best to connect the devices as shown in the diagram, if it still doesn't work - go to Step 2. |
| Line 92: | Line 64: |
| Created by DonPark and CalebPhillips over beers at NodeLuckyLab. | Created by DonPark and CalebPhillips over beers at NodeLuckyLab. Updated by DanRasmussen. |
Node Owner Help
An accessible and concise guide to basic troubleshooting internet connection problems with a Personal Telco node.
The most recent version of this document will always live here: https://personaltelco.net/wiki/NodeOwnerHelp. The version you are viewing is current as of 2025-07-31.
Contents
Troubleshooting
This section assumes you have a wireless-enabled device, and that you're unable to connect to a Personal Telco node. This is a flowchart: start at the first step and work your way through until you solve the problem.
Step 1. Can you see the ESSID?
Each wireless network your computer can see is identified by its ESSID (or Network Name). A Personal Telco node, by definition, has an ESSID of "www.personaltelco.net". If you can see "www.personaltelco.net" in your computer's list of available wireless networks, go to Step 4, otherwise, go to Step 3.
Step 2. Contact the PTP
If you've arrived at Step 2, the solution to your technical issues isn't covered in this troubleshooting guide. Please contact us at info@personaltelco.net, describing the problem and the steps you've taken to solve it.
Please let us know if this document was (or wasn't) helpful.
Step 3. Make sure the Access Point has Power
Your access point is most likely a small device with an antenna connected to it. Find it, and make sure it is powered on. If it is, go to Step 2, otherwise, plug it in and go to Step 1.
Step 4. Get an IP Address
Your device should get an IP address from the Node. If you use Windows, try this:
go to Start -> Run
- type "cmd", Enter
- in the black box, type "ipconfig", Enter
Do you see an IP address? Most likely it looks something like: "192.168.0.101" (TODO: add screen shot)
If not, try this:
- in the black box, type "ipconfig /release", Enter
- then type, "ipconfig /renew", Enter
- finally type, "ipconfig", Enter
Do you see an IP address now? If not, go to Step 7, otherwise go to Step 5.
Step 5. Open a Webpage
Open your web browser -- we recommend Mozilla Firefox, if available for your device, and recommend not using Internet Explorer.
Open any webpage, e.g. http://google.com. Can you see it? If you have a captive portal, you should see the splash page (with the Personal Telco logo) - if so, click "Accept", then visit http://google.com.
At this point, you should see the website you wanted (e.g. Google) If so, go to Step 6. Otherwise:
Go to Step 7 if it says something like "google.com cannot be found"
- Go to Step 7 if it says something like "... is not responding" or "... cannot be contacted
Step 6. Everything is Okay?
If you reached here, it seems like all is well. If not, perhaps you have a problem not covered in this document: go to Step 2.
Step 7. Investigate Wiring Problems
http://www.personaltelco.net/~caleb/diagrams/PotentialNodeOwner2.png
Your setup might look something like the above diagram. You will have a DSL modem, a Access Point, and often, a Captive Portal. Make sure these are connected to each other as shown. Also, at each connection check for a little green light - this is the "Link Light." If it isn't lit, then either the other end is disconnected or the wire is damaged. If you think everything is connected properly, go to Step 2. If not, do your best to connect the devices as shown in the diagram, if it still doesn't work - go to Step 2.
Credits
Created by DonPark and CalebPhillips over beers at NodeLuckyLab. Updated by DanRasmussen.